Table of Content
Then, you will need to cut through the damaged boards with a saw. Once the boards are cut, you can remove them and replace them with new boards. There are a few things that can cause a floor to sag in a mobile home. One of the most common causes is a lack of support underneath the home.
If your flooring is 3/4″ set your circular saw to that and follow the perimeter along the edge of the room. For bathroom or kitchens consider marine-grade plywood. It’s more expensive but it has waterproofing so it stands against water better. The most difficult parts of the job are removing the old flooring, building out the perimeter joists, and keeping everything level. If you have potted plants in your mobile home, check underneath them occasionally for soft spots.
How to Fix a Sagging Floor in a Mobile Home?
You can also buy a ceiling kit at Lowe’s that is in different patterns such as shiplap. We’ve used beadboard paneling in a few mobile homes too. There are a lot of options but I’ll be honest, ceilings are not easy. Just looking up all day is a pain and then dealing with the seams is another big pain. It’s a job but it makes the whole home look completely different.
Inspections are a necessary evil in the construction world, regardless of what kind of DIY project you do. Every location, whether in Canada or America, has building codes that must be met for all update and remodeling projects. The location of your home will impact the codes that you will need to meet. Homes in Canada face different issues than homes in Florida so be sure to research your local codes. Depending on your location you may qualify for a program or financing help to get your mobile home insulated better, especially if it was built before 1976.
Determine The Area To Be Repaired
The couple’s new vintage mobile home had served Laurel’s aunt very well until she passed last year at the age of 93. While the mobile home’s decor may not have made it to the cover of Home and Garden, auntie had lovingly updated it over the years. She had heroically painted the walls herself with a three-inch paintbrush in bright yellow and aqua. It is made from the same closed cell foam beads that your coffee cups and shipping peanuts are made from.
I was sick again after the water damage was repaired and a new carpet installed in the living room. My little dog and I suffered together, and before the year was out, he died of lung cancer. You can buy the replacement ceiling panels at your local mobile home supply store. You’ll simply rip out the old and lay in the new over the wall lip.
Complete your own mobile home floor replacement
You will likely have the best luck finding someone by calling your local mobile home supply store. They will at least know which local companies will work on manufactured housing and that’s a good start. Subflooring is a standard construction issue in both mobile homes and traditional site-built homes so perhaps going on HomeAdviser.com and looking for flooring help. A pneumatic “palm nailer” or small impact driver makes it much easier to install support blocking on floor joists. I’ve done this job before in a mobile home and in a few stick frame houses due to pet damage and water damage in bathrooms. The smaller the pieces, the easier it is to get them out of your way.
It is necessary that all edges of the new subfloor are supported underneath and can be attached with screws. The easiest way to begin removing the subfloor, is to use a large hole saw or a jigsaw and cut out from the hole in the floor or a piece of the soft spot in the floor. Once you locate where the joist are, then you can use the saw to cut along the side of the joist. The subfloors of many older manufactured homes tend to be made of dense particle board. Over the years, this type of subfloor has the tendency to break down in heavy traffic areas within the home. First, you will need to remove the baseboards and any other trim around the floor.
Usually, tackling a project requires multiple sites and multiple opinions. Since I knew in my mind I had to insulate between the joists then cover that insulation, I set out to find help. I found the only instructions I needed, and it is so thorough, I can’t wait to get started this weekend. Having a hard time finding insulated skirting for my mobile. Currently have skirting on, live in Wisconsin where it gets a little cold sometimes. Also gaps in the underbelly as well as visible ductwork.
I’m not sure about luxury vinyl (I’ve never been able to afford it). I do know that the cheap laminate floating floor worked just fine over the older pile flooring in our single wide bedroom. That was also the warmest room in the house and I think it was from that extra layer of the carpet.
So, I’ve always been told that you should always have a belly wrap and a ground covering. It’s at least another layer of protection from critters. However, you’ll would want to make sure you have ample ventilation. Fire is probably the biggest disadvantage of foam board insulation and meeting your local fire protection codes may be bothersome. Foam is fairly hard to ignite, but once it catches it emits a dense smoke and toxic gases.
You’ll pay more for extruded polystyrene but you’ll get better energy efficiency. The R-value of extruded polystyrene is around 5 per inch. Expanded polystyrene is the most common type of foam insulation and the most affordable. Without looking at it I can’t really give you much of a suggestion. Based on what you’ve described, I can assure you that you are looking at a LOT of work and a lot of expensive materials.
You will need to remove the base underneath the damaged floor. Then use a self-leveling patch to the damaged area. It will level the sagging mobile homes underneath the floor. Then you can use mortar to stabilize the underneath floor.
Use a level to locate where the floor is sagging. It will help you to give straight support to the saggy floor. Product 01Product 02The quality of these vapor barriers is outstanding.
Replacing Mobile Home Floors
You can either reinforce the floor joists or replace them . If you have a carpet or other cover over your plywood floor you should remove this first. It might be secured around the perimeter of the room with corner strips. Both can be removed simply enough by using screwdrivers, carpet knives, and the hammer by prying out nails or staples and pulling them up. I’m thinking we’ll want to lay down a moisture barrier between the flooring and the subfloor, as well as put in real plywood.
No comments:
Post a Comment